How to Cast Off Knitting (Bind Off)

How to cast off knitting, in one sentence: knit two stitches, lift the first stitch over the second and off the needle, then repeat across the row until one stitch remains, which you secure by pulling the yarn tail through it. Casting off — called binding off in US patterns — finishes your work so the last row cannot unravel. This page teaches the standard method, a stretchy method for edges that need to give, and casting off in the round, plus how to fix the tight edge that troubles most beginners.
The Standard Cast-Off, Step by Step

- Knit two stitches onto the right needle, as normal.
- Lift the first stitch over the second. Insert the left needle tip into the first stitch (the one farther from the needle tip), lift it up and over the second stitch, and let it drop off the needle. One stitch remains on the right needle.
- Knit one more stitch. Now there are two stitches on the right needle again.
- Repeat. Lift the first over the second, knit one more, lift, knit — across the whole row.
- Finish. When one stitch remains, cut the yarn leaving a tail of a few inches, pull the tail through the last loop, and tighten gently. Weave the tail into the fabric with a yarn needle.
That is the whole method. It is simple, secure, and suits most projects — scarf ends, blanket edges, and any edge that does not need to stretch much.
Casting Off Purlwise
If your last row is a purl row, or your pattern says "bind off in pattern," you cast off purlwise: purl two stitches instead of knitting them, then lift the first over the second exactly as above. The principle is identical; only the stitch type changes. Casting off in pattern — knitting the knit stitches and purling the purl stitches as you cast off — keeps ribbed edges looking like ribbing instead of flattening them into a knit edge.
The Stretchy Cast-Off
The standard cast-off can be too tight for edges that must stretch: hat brims, sock cuffs, necklines. A tight cast-off on a hat brim makes the hat hard to put on; on a neckline, it makes the opening uncomfortable.
The simplest stretchy fix is to cast off with a needle one or two sizes larger than your working needle. The larger needle makes larger loops, and the edge gains stretch without any change in technique.
A second method, the yarn-over stretchy cast-off, adds stretch by working a yarn over before each stitch: knit one, yarn over, lift the yarn over and the previous stitch over the new stitch, repeat. This makes a noticeably more elastic edge and is worth learning for socks and fitted cuffs. Use it when the larger-needle trick is not stretchy enough.
Casting Off in the Round
When knitting in the round — a hat, a sock, a sleeve — there is no end of row to turn at, so casting off joins the round into a finished edge. Work exactly as above, knitting (or working in pattern) and lifting stitches over, all the way around until one stitch remains. The join point can leave a small step where the round began; weaving the tail through the first cast-off stitch and back smooths it out. For a hat crown, the last stitches are usually gathered rather than cast off — the pattern will say "thread yarn through remaining stitches and pull tight" — which is a different finish from casting off, used to close a small opening.
The Tight Edge Problem (and How to Fix It)
The most common beginner cast-off problem is an edge that pulls in and puckers. Causes and fixes:
- Pulling the yarn tight after each stitch. Keep your tension loose on the cast-off row. The stitches should slide along the needle, not grip it.
- Lifting stitches over with force. Lift gently and let the stitch drop; yanking it tightens the row below.
- Using the same needle size on a stretchy edge. Switch to a needle one or two sizes larger for the cast-off row.
- An already-tight edge. If the edge is cast off and too tight, there is no way to loosen it without undoing it. Undo the cast-off row back to live stitches and redo it loosely — a few minutes of rework beats a finished piece that does not fit.
Cast-Off vs Cast-On: Do They Need to Match?
Not exactly, but they should be similar in stretch. A very stretchy cast-on paired with a tight cast-off gives a piece with one end that gives and one end that does not — noticeable on a scarf, uncomfortable on a hat. As a rule, use the same needle size for both edges, and if you used a larger needle for the cast-on, use a larger needle for the cast-off too.
Frequently Asked Questions
How do you cast off knitting?
Knit two stitches, lift the first over the second and off the needle, knit one more, and repeat across the row. When one stitch remains, cut the yarn, pull the tail through the last loop, and weave in the end.
What is the difference between cast off and bind off?
Nothing — they are the same technique. UK patterns say "cast off" and US patterns say "bind off". This site uses "cast off" with "bind off" noted, so either term in a pattern will make sense.
How do you cast off loosely in knitting?
Cast off with a needle one or two sizes larger than your working needle, and keep your tension loose — do not pull the yarn tight after each stitch. For a very stretchy edge, use the yarn-over stretchy method described above.
How do you bind off in the round?
Work the same lift-over method all the way around the round until one stitch remains, then pull the tail through it. Smooth the join point by weaving the tail through the first cast-off stitch.
Why is my cast-off edge too tight?
Usually because of tight tension on the cast-off row, or because the standard method was used on an edge that needs to stretch. Redo the row loosely, with a larger needle if needed.